Support VWWC - everywhere else

Search:

Type: Posts; User: hamza; Keyword(s):

Page 1 of 13 1 2 3 4

Search: Search took 0.01 seconds.

  1. Thread: 2016 dyno day

    by hamza
    Replies
    40
    Views
    4,315

    SA I don't know about that, I'll be going for the...

    I don't know about that, I'll be going for the wooden spoon :D
  2. Thread: 2016 dyno day

    by hamza
    Replies
    40
    Views
    4,315

    SA Pencil me in, will be running my daily, e30 318i,...

    Pencil me in, will be running my daily, e30 318i, keen to see what it will make :D
  3. If the wires run over the strut towers then yes...

    If the wires run over the strut towers then yes please.

    I didn't rewire the front. The photo I posted if off another car and is identical as to how my wires were.
  4. Picture request - early Mk3 vr6 engine bay wiring.

    Hi guys.

    I am im slowly beginning to reassemble my 3dr vr swap and am having an issue with rewiring the engine bay. The donor vr was a early (94) 4 door car in dark red (maroon) and the 3 door...
  5. I think the later cars came out with a carpeted...

    I think the later cars came out with a carpeted boot. My 95 vr6 is bare like the op but my 97 cl has carpets covering sides and below tailgate.
  6. Replies
    13
    Views
    4,503

    Also i was told that the bumper on the vento is...

    Also i was told that the bumper on the vento is deferent in that it extends a little further forward, but no fitment issues.
  7. Replies
    40
    Views
    6,779

    The way you describe the car, 5 door CL, peeled...

    The way you describe the car, 5 door CL, peeled clear (needs a full srepray as the paint now has faded due to failed clear) it is probably the most unwanted spec'c mk3 right now. The sentimental...
  8. Replies
    3,923
    Views
    255,138

    Imo you would be best off getting 25 or 50ml of...

    Imo you would be best off getting 25 or 50ml of paint from a paint supplier that can match the paint directly off your car as it probably has faded a little by now.

    Also this thread is on page 333...
  9. Replies
    1
    Views
    558

    2D CL to VR6 swap wiring question

    Hi guys, i have done some searching and was not able to get an answer, when performing a vr6 swap into a 1.8 cl, how much of the wiring do you swap over? All of it inc the fuses and behind the dash...
  10. Thread: A/C Issue

    by hamza
    Replies
    26
    Views
    2,505

    As far as i know, no they aren't. My vr...

    As far as i know, no they aren't. My vr compressor had a sticker saying 6 zylinder and the CL i parted out had a sticker 4 zylinder.
  11. Replies
    27
    Views
    6,605

    My 94 vr doesn't have a immobilizer but the 96 CL...

    My 94 vr doesn't have a immobilizer but the 96 CL that i just parted out did. Its a ring that goes around the ignition barrel and accepts signals from a chip in the key. Cutting the key wasn't...
  12. Replies
    18
    Views
    2,580

    VIC just don't do it yourself :D ...

    just don't do it yourself :D

    https://www.youtube.com/watch?v=lKyqiGyu0Jk
  13. Thread: Juzz's new VR6

    by hamza
    Replies
    466
    Views
    44,118

    Not a bad idea with the welding of the rear...

    Not a bad idea with the welding of the rear doors, the doors on my 2d are very long.
  14. SA Yea i ordered obd2 parts, have fitted them...

    Yea i ordered obd2 parts, have fitted them already, will let people know how it goes.
  15. Thread: VR6 Fuel Economy

    by hamza
    Replies
    56
    Views
    6,925

    obd 2 is a plug n play whereas obd1 has to be...

    obd 2 is a plug n play whereas obd1 has to be soldered in :(
  16. do you know what exactly is required? and is that...

    do you know what exactly is required? and is that the only issue?
  17. Replies
    3
    Views
    834

    SA Will i have any issues if i fit them?

    Will i have any issues if i fit them?
  18. vr6 upper timing chain guide and tensioner early vs late

    Hi guys, i am in the process of doing a timing chain service and accidentally ordered the later top guide rail and tensioner. I have since done some research and have found out that the new style...
  19. Replies
    3
    Views
    834

    SA vr6 late timing chain and top tensioner

    Hi, i accidentally ordered these instead of the early style, so these are up for sale.
    (if you have new early ones, please pm me)

    asking $50 ono posted aus wide
    ...
  20. SA vr6 early chain tensioner and top guide rail

    Hi all, as the post states, i accidentally ordered the late vr parts (which will be in the for sale section).

    let me know what you have.
  21. Replies
    2
    Views
    501

    your inbox is full..

    your inbox is full..
  22. Replies
    2
    Views
    501

    I have one, pm me.

    I have one, pm me.
  23. Replies
    16
    Views
    3,471

    How much? (Borat voice)

    How much? (Borat voice)
  24. Replies
    16
    Views
    3,471

    Update: I am about to order my parts hoard...

    Update:

    I am about to order my parts hoard from ecs and have a question. Do i have the dual upper chain or the single?

    heres a pic for ref and a pic of the engine number if that helps.

    19685...
  25. Replies
    16
    Views
    3,471

    Sweet! i was just about to ask re the booster. ...

    Sweet! i was just about to ask re the booster.

    thanks
Results 1 to 25 of 322
Page 1 of 13 1 2 3 4
| |