r32 APR ECU upgrade issue

hey guys the r32 i own has a APR ecu upgrade in it and it has been tuned for three setups.
(1) 95
(2) 98
(3) valet
it the manual i got with it it tells you how to change the modes. ' step 1 Press and hold the "set" button on your cruise control. After approximately five seconds, the "check engine" light on your dash will begin to blink once per second. This will tell you that you are activating program one. This blinking sequence will continue for approximately five seconds. After this five second interval, the "check engine" light will begin blinking twice per second. This will indicate that you have activated the second program. This process is continued to access any remaining programs you may have purchased. (three blinks = program three, four blinks = program four).
Step 2 Once you have activated the desired program, simply release the "set" button. The "check engine" light will stop flashing. Turn the ignition key off for 10 seconds, turn the key back on, and you will be locked in that program until you change it again.

i do this and the engine light does not come on at all. (any feed back would be swell guy cheers in advance)

Yes that is correct mate.
So you put your key in and turn the ignition on?

Then turn the cruise control on?

Then you hold the set button and then the engine light will start flashing.

Is this what you do mate?

had the car serviced recently? They may have wiped the tune.

Quote:

---

Originally Posted by isaac32

hey guys the r32 i own has a APR ecu upgrade in it and it has been tuned for three setups.
(1) 95
(2) 98
(3) valet
it the manual i got with it it tells you how to change the modes. ' step 1 Press and hold the "set" button on your cruise control. After approximately five seconds, the "check engine" light on your dash will begin to blink once per second. This will tell you that you are activating program one. This blinking sequence will continue for approximately five seconds. After this five second interval, the "check engine" light will begin blinking twice per second. This will indicate that you have activated the second program. This process is continued to access any remaining programs you may have purchased. (three blinks = program three, four blinks = program four).
Step 2 Once you have activated the desired program, simply release the "set" button. The "check engine" light will stop flashing. Turn the ignition key off for 10 seconds, turn the key back on, and you will be locked in that program until you change it again.

i do this and the engine light does not come on at all. (any feed back would be swell guy cheers in advance)

---

Are you getting the blinking sequence at all? if you are not - you probably have the ECU in "Security lockout" which prevents changing of programs. You have to enter your PIN number to unlock firstly.

If the battery has been disconnected (or run flat) then it defaults to locked.

How long ago did you get the upgrade?

the upgrade was installed in 2006. i have only had the car for 5ish months. i do have the code but where do i enter it?? do i have to get to the ECU and punch it in manually or do i need to take it to a APR approved supplier. thanks in advance

Make sure the cruise control stalk is set in the off position before you do the sequence, see if that works Isaac.

Quote:

---

Originally Posted by robbie

Make sure the cruise control stalk is set in the off position before you do the sequence, see if that works Isaac.

---

yeah i have tryed pretty much ever combination to get it to work and still nothing.

Quote:

---

Originally Posted by robbie

Yes that is correct mate.
So you put your key in and turn the ignition on?

Then turn the cruise control on?

Then you hold the set button and then the engine light will start flashing.

Is this what you do mate?

---

You have to have the cruise already on and hold in the set button as you turn on the key

Keep holding the set button until you get the desired number of flashes of the engine symbol for the program you're after.
Then let it go, turn your key off for a few secs and that should be it


Sent from my iPhone using Tapatalk

[QUOTE=BLKMKV;1018699]You have to have the cruise already on and hold in the set button as you turn on the key

Keep holding the set button until you get the desired number of flashes of the engine symbol for the program you're after.
Then let it go, turn your key off for a few secs and that should be it

just tried that then and nothing no flashes of the engine light at all. is this APR ecu upgrade a full ecu or just a attachment thing ?

Apr upgrade is a reflash of your stock ecu, it must be locked somehow, I would be taking it to your nearest apr dealer to sort it


Sent from my iPhone using Tapatalk

and this time just get the '98' tune and nothing else!! Much easier!!!

Quote:

---

Originally Posted by BLKMKV

Apr upgrade is a reflash of your stock ecu, it must be locked somehow, I would be taking it to your nearest apr dealer to sort it


Sent from my iPhone using Tapatalk

---

yeah think thats what i might do thanks mate

Try unlocking or locking the ecu. I don't know what your code is I'm hoping you know it. They normally set it to something easy with low numbers.

You could try resetting the ecu by unhooking the battery over night.


There are two APR dealers down your way that will be able to sort it out for you.

Canberra VW Centre Kiama
Unit 13/2 Brown Street
Kiama NSW 2533
[p] 02 4233 2797
[e] kiama@cvwc.com.au
[w] www.cvwc.com.au

Dunham Auto Repairs
617 Princes Hwy
Woonona NSW
[p] 02 4284 3666

so guys i finally got it sorted the tune was locked in valet mode. i drove down to canberra vw centre in kiama and all that needed to be done was enter the code given to me and BAM all is good and my tune is working and i can go faster. happy days

Nice, good to hear, enjoy


Sent from my iPhone using Tapatalk