OBD11 modifications

[Flipper Dog]

Confirmed changes using OBD11 on a MY21 T-ROC with MIB3:


Change clock display from 24 hour format to am/pm

Adaptation
Control unit: 17 Dashboard
Name: Units adjusted
Values:
Time:
Old value: 24h
New value: 12h AM_PM

---------------------------------------------------------------
Changing setting for lane departure warning

Adaptation
Control unit: A5 Driver Assistance
Name: Warning intensity, lane depart. warning
Values:
---:
Old value: Medium
New value: Selection via menu

---------------------------------------------------------------
Remembing driver's seat heat setting

Adaptation
Control unit: 08 Air Conditioning
Name: Retention of driver's seat heater level
Values:
---:
Old value: active for 10 minutes
New value: active

---------------------------------------------------------------
Changing setting for adaptive lane guidance

Long coding
Control unit: A5 Driver Assistance
Values:
Point_of_intervention:
Old value: late
New value: early (setting via menu)

---------------------------------------------------------------
Display AC blower speed

Long coding
Control unit: 08 Air Conditioning
Values:
Blower display in auto operation:
Old value: Not activated
New value: activated

---------------------------------------------------------------
Prevent ACC slowing down when passing vehicle in right lane

Long coding
Control unit: 13 Adaptive Cruise Control
Values:
Overtaking_right_prevention:
Old value: activated
New value: Deactivated

---------------------------------------------------------------

[doc_777]

Rear wiper dwell/intermittent cycle time (this worked successfully on my 2021 140 sport):

Rear Wiper Delay
09 - Central Electrics
Adaptations
Security Code 31347
Rear Wiper
Select Einzelansteuerung Heckintervallwischen:
Change to: Unabhaengig_der_Fahrzeuggeschwindigkeit (stock = "not active")

Select Einzelansteuerung Heckintervallwischen Zeitintervall 1
Change to: 15s (stock = 7s)

[Flipper Dog]

Traffic sign recognition - MIB3
This will work for Australian models.
Coding is by OBD11.
You will need to open the bonnet for this to apply.

To display the speed limit on the driver's display. This coding will use road sign detection mode not fusion mode. The front camera will only read speed limits not use any data with speed limits loaded within the maps.


A5-Driver Assistance
Click on Long coding
Press the button on the top right that shows a '0' and '1' to see it Bytes mode; Each Byte has 8 bits (from 0 to 7 included)
Press the right arrow down until you reach Byte 16
Inside Byte 16 activate bit 4 and do not modify the rest
Press the Validate button
Exit Module A5 and enter Module 5F
Click on Adaptation
Search for Vehicle Menu Operation
Enter menu_display_road_sign_identification and change to Active
Enter menu_display_road_sign_identification_over_thresho ld_high and change to Active
Press the Validate button
Go back to Adaptation and look for Vehicle Function List BAP
Enter traffic_sign_recognition_0x21 and change to Active
Enter traffic_sign_recognition_0x21_msg_bus and change to ' Data Bus Infotainment'
Exit Module 5F and enter Module 17
Click on Long Coding
Press the button on the top right that shows a '0' and '1' to see it Bytes mode; Each Byte has 8 bits (from 0 to 7 included)
Down, press the right arrow until you reach Byte 5
Inside Byte 5 activate bit 2 and do not modify the rest
Press the Validate button
A5-Driver Assistance
Click on Adaptation
Road sign detection fusion mode
Change to "Road sign detection" (Road sign fusion)
Security Key: 20103
Press the Validate button

Restart the Infotainment by pressing and holding the power button between 10s to 15s and release.
In the settings of the driving assistants, the option 'Dynamic Road Sign Display' should appear. Tick "Show in instrument cluster" and "Speed warning" to "Visual".
There is also an option to warn when exceeding the speed.

Note: You will now get a warning which indicates that signal recognition is limited. This warning will appear for a few seconds in the instrument cluster after you drive off. This message is only informative and does not produce any problem, error or failure. The recognition of signals will work normally but limited because it is not using the data from the maps.
School zones at 40km/h will be detected as 40km regardless of the main speed limit and will show as a speed warning when you pass them.

NOTE:
This coding was developed using the 3Q0 front camera (A5 driver assistance).
If you have a 2Q0 front camera the final drivers assistance part to change to "Road sign detection fusion mode" is not available.

[Hillbilly]

Be interesting to see if this will work in our Kamiq when it arrives.

Is almost identical to what you do in a TIguan and Golf Mk7

I have found that it is best to put the security code in first before coding or it wont let you do it (sometimes)

[Grugly]

Hey @flipper - just picked up our Tiguan R and followed the instructions for the MIB 3 unit. Everything's works until getting to road side fusion where it is saying function not available.

In OBDeleven also byte 5 has been renamed so no longer shows bits. However there was an option names Traffic sign recognition in the third row that I assumed to be the same as bit 2..

I'll keep investigating to see if there is a way to change the bit

[Hillbilly]

Hey @flipper - just picked up our Tiguan R and followed the instructions for the MIB 3 unit. Everything's works until getting to road side fusion where it is saying function not available.

In OBDeleven also byte 5 has been renamed so no longer shows bits. However there was an option names Traffic sign recognition in the third row that I assumed to be the same as bit 2..

I'll keep investigating to see if there is a way to change the bit

Well all that is available for my Kamiq 21 but what I want to know does it work for a 2Q camera as a lot of stuff wont as most have a 3Q camera

[Bambazonke]

Hi there Flipper Dog
I have a MY21 T Cross with a 2Q Valeo A5 ECU and am trying to activate Sign Assist without much luck to date. Coding in the 17 kombi and 5F MIB3 (without Nav) head unit appears to be the same at the T Roc Tiguan Golf etc. However in the A5 camera ECU instead of Byte 16 bit 4 it is a combination of codes in Byte 12 Bits 3 to 7. I have tried a number of combinations here and it still does not work.
I am also not sure if it is a bus setting in the 5F ECU as I have seen Extended, Infotainment and Comfort options all being used but this may because different head units may have been installed. At this stage I am leaning on the Infotainment option.

In VCDS I am able to see 3 "fusion" options in the Adaptations drop down menu which are currently set to activated, road sign detection and the numerical value of 0. Are you able to see this last setting in OBD Eleven and if so what is the value?
Thanks

[Hillbilly]

Hi there Flipper Dog
I have a MY21 T Cross with a 2Q Valeo A5 ECU and am trying to activate Sign Assist without much luck to date. Coding in the 17 kombi and 5F MIB3 (without Nav) head unit appears to be the same at the T Roc Tiguan Golf etc. However in the A5 camera ECU instead of Byte 16 bit 4 it is a combination of codes in Byte 12 Bits 3 to 7. I have tried a number of combinations here and it still does not work.
I am also not sure if it is a bus setting in the 5F ECU as I have seen Extended, Infotainment and Comfort options all being used but this may because different head units may have been installed. At this stage I am leaning on the Infotainment option.

In VCDS I am able to see 3 "fusion" options in the Adaptations drop down menu which are currently set to activated, road sign detection and the numerical value of 0. Are you able to see this last setting in OBD Eleven and if so what is the value?
Thanks

Further to my previous posts my Kamiq has roadside sign recognition from factory but I cant get it to show in the Dash, even though that is ticked in the MMI You have to change fusion to plain recognition as fusion doesnt work in our maps

[Flipper Dog]

@Bambazonke
Is this what you are looking for in A5 Control unit Adaptation?

[Hillbilly]

Is this what you are looking for in A5 Control unit Adaptation?

Are you replying to me or him. Ive got it sorted in both the Kamiq and the Tiguan. Difference is the Tig has a 3Q0 camera and the Kamiq has a 2Q0 which isnt able to be coded very easily, if at all it seems