Preen59
19-03-2011, 03:13 PM
First up, Mods, i didn't know where to put this, so here it is. Place it where you like...
So.. Last night i'm driving along, going to pick a friend up from the Pub.. At the last second I see a concrete block in the middle of the road. I didn't have time to avoid it and BANG!! (sump) ....... BANG (rear axle).... OH ****, this isn't good.
By the time i'd pulled up there was already a slick behind me. I looked underneath and the sump was busted, oil dripping out. I thought bugger it, i'll see if i can get home before the oil light comes on! haha.. I made it 2 blocks.
(Sorry for the ****ty phone pics)
http://i280.photobucket.com/albums/kk182/preen59/IMG00073-20110319-0055.jpg
So.. I grabbed my jacket out of the back and started on the long walk home..
Tilt trayed it to the shop this morning and put it on the hoist to assess the damage.
A quick wash with carby cleaner to see what we were up against..
http://i280.photobucket.com/albums/kk182/preen59/IMG00075-20110319-1149.jpg
Oil pump was undamaged (Thank christ/god/allah/your homeopath)
http://i280.photobucket.com/albums/kk182/preen59/IMG00078-20110319-1235.jpg
So.... grab that stick of Knead It! (Awesome ****, we use it to bog alloy vacuum form moulds at work)
First up a damn good clean with carby cleaner to remove all the oil residue etc. Then we tried our best to straighten it up without busting it further using a hammer and a block of wood.
Using the bits that were broken out we carefully glued them back it with knead it (it's a bit like sticky plasticine before it sets). I had to make a couple of little sections to fill the gap out of some 3mm alloy, but nothing too drastic. Once one side sets, you can fill the other side and push it right in hard to make sure it fills and seals properly.
http://i280.photobucket.com/albums/kk182/preen59/IMG00079-20110319-1307.jpg
Once it sets, clean the sealing faces, put some sealant on the sump and put the sump back on..
http://i280.photobucket.com/albums/kk182/preen59/IMG00080-20110319-1348.jpg
Fill it with oil and go nuts!
I must stress that, although knead it is damn good stuff and will most likely seal for a VERY long time, I am only using this as an interim measure.
I have a fully baffled, windaged fabricated alloy sump leaving INA Engineering on Monday (With Corey's oil cooler kit, actually!). I'll chuck up some pics when it turns up and I fit it. :)
http://a5.sphotos.ak.fbcdn.net/hphotos-ak-snc3/21972_330013624991_294598024991_4919297_5019616_n. jpg
If you want more info on doing this, hit me up.. But I must stress that it's not a job for the faint hearted. :)
Cheers guys!
So.. Last night i'm driving along, going to pick a friend up from the Pub.. At the last second I see a concrete block in the middle of the road. I didn't have time to avoid it and BANG!! (sump) ....... BANG (rear axle).... OH ****, this isn't good.
By the time i'd pulled up there was already a slick behind me. I looked underneath and the sump was busted, oil dripping out. I thought bugger it, i'll see if i can get home before the oil light comes on! haha.. I made it 2 blocks.
(Sorry for the ****ty phone pics)
http://i280.photobucket.com/albums/kk182/preen59/IMG00073-20110319-0055.jpg
So.. I grabbed my jacket out of the back and started on the long walk home..
Tilt trayed it to the shop this morning and put it on the hoist to assess the damage.
A quick wash with carby cleaner to see what we were up against..
http://i280.photobucket.com/albums/kk182/preen59/IMG00075-20110319-1149.jpg
Oil pump was undamaged (Thank christ/god/allah/your homeopath)
http://i280.photobucket.com/albums/kk182/preen59/IMG00078-20110319-1235.jpg
So.... grab that stick of Knead It! (Awesome ****, we use it to bog alloy vacuum form moulds at work)
First up a damn good clean with carby cleaner to remove all the oil residue etc. Then we tried our best to straighten it up without busting it further using a hammer and a block of wood.
Using the bits that were broken out we carefully glued them back it with knead it (it's a bit like sticky plasticine before it sets). I had to make a couple of little sections to fill the gap out of some 3mm alloy, but nothing too drastic. Once one side sets, you can fill the other side and push it right in hard to make sure it fills and seals properly.
http://i280.photobucket.com/albums/kk182/preen59/IMG00079-20110319-1307.jpg
Once it sets, clean the sealing faces, put some sealant on the sump and put the sump back on..
http://i280.photobucket.com/albums/kk182/preen59/IMG00080-20110319-1348.jpg
Fill it with oil and go nuts!
I must stress that, although knead it is damn good stuff and will most likely seal for a VERY long time, I am only using this as an interim measure.
I have a fully baffled, windaged fabricated alloy sump leaving INA Engineering on Monday (With Corey's oil cooler kit, actually!). I'll chuck up some pics when it turns up and I fit it. :)
http://a5.sphotos.ak.fbcdn.net/hphotos-ak-snc3/21972_330013624991_294598024991_4919297_5019616_n. jpg
If you want more info on doing this, hit me up.. But I must stress that it's not a job for the faint hearted. :)
Cheers guys!