.
The filter he is talking about is the receiver drier in the gas system, not the cabin filter in the car.
You can check the operation of the control valve in the compressor with a scope...
Type: Posts; User: MHAuto; Keyword(s):
.
The filter he is talking about is the receiver drier in the gas system, not the cabin filter in the car.
You can check the operation of the control valve in the compressor with a scope...
5x120, try and go for genuine mags, much stronger than the aftermarket and you won't have any load rating issues.
The model is known as a T5.1GP, the GP part is german for face lift.
Cheers.
Are you seriously telling him to crack open high pressure lines on common rail system? Are you trying to kill someone? Do you know what type of pressure your dealing with?
What are your...
Start and stall with throttle input is an immobiliser fault.
Start and keep running with throttle input, sounds like a throttle body assembly fault,does it compensate for loads when the car is...
Have your codes checked, sounds like a boost pressure not reached situation, you probably have a boost pressure leak and the ecu is going in to failsafe when boost pressure is not reached when...
McGraths Hill Automotive is looking for an experienced Vw , European car mechanic to start ASAP . Very well equipped clean modern European car workshop located in McGraths Hill , pm or call for more...
Do you work in VW specialist workshop/dealer?
Do a search, or look a couple of threads down the page, T5.2 oem radio options. Been covered alot before.
Has anyone done trailer hitch coding with VCDS on a 7P Touareg?
The Ross Tech site has the heading but no link for 7P'S
Setting the pump timing by lift at TDC will get you in the ball park, but should be fine tuned with a scan tool to be 100% correct. See a VW specialist that knows what their doing and have it...
If you can get us a fault code(s) we might be able to help a bit more rather than speculate.
Stub shaft and c.v. shaft are both available seperatly from VW, very common issue, i think stub shaft is about $400 and driveshaft is exchange from VW at about $550 i think, be carefull with the...
Do you know what the wires are? Do you have a diagram or instructions?
Whats the chance of vcds printout of what modules you have on your bus, i tried doing it and nothing worked, i think there is three diferent modules (low,mid,high) but not sure which one i have, i...
Not a big fan of the v10, the v6 and v8 tdi are better motors.
A sales manager at VW i spoke to a while back said he had heard rumours of VW R+D putting a V10 in 'rok , and they were doing...
Its the same fault, ecu is registering the fault for the brake switch and showing glow light as fault recognition, change the switch and clear fault ( it will have an implausable brake light switch...
Do you know what the bcm part numbers are that support it or don't support it?
Hello all,
Does any one know the procedure for fitting a MFSW with Paddles to a T5.2 that originaly had no MFSW, i know the retro fit for a car with a MFSW to MFSW with paddles is just a coding...
The problem with Dealerships is you may get good service by one tech that knows what he's doing and cares and the next time you don't know who your going to get, there's so many inconsistancies.The...
How long between DPF light coming on and new sensor being fitted?? while the DPF light is on the car won't do it's regens while in limp mode, this can cause DPF to block up, If there was enough time...
I was told by VW when they started the exchange program it was because of German recycling laws, that all companies have to offer recycling as Germany was going to 0 landfill, which i think they are...
Give me a call at work 45 777 540 and i'll be able to help more. Ask for Dave.
The map sensors can be replaced in your original ecu, there are companies in Sydney doing this repair work.
Newbie post.