Results 1 to 3 of 3

Thread: DSG Re-Calibration OBDeleven?

  1. #1

    DSG Re-Calibration OBDeleven?

    Hi Guys,

    For 2008/9 Passat R36, what tool do i need to run the DSG Re-cal, the one that takes 5-6 mins of clicking and clacking solenoids firing and clunking etc...

    can this be done with OBDeleven much in the same way the throttle body re-cal can be done?

    Cheers,
    Mat

  2. #2
    Join Date
    Sep 2013
    Location
    Victoria
    Posts
    1,732
    Users Country Flag
    Quote Originally Posted by MatC View Post
    Hi Guys,

    For 2008/9 Passat R36, what tool do i need to run the DSG Re-cal, the one that takes 5-6 mins of clicking and clacking solenoids firing and clunking etc...

    can this be done with OBDeleven much in the same way the throttle body re-cal can be done?

    Cheers,
    Mat
    Mat - haven't done it myself, but should be exactly the same as this - taken from Ross-Tech website:

    Quote Originally Posted by Ross-Tech
    6-Speed Direct Shift Gearbox (DSG/02E)

    Basic Setting

    Prerequisites:


    • Fluid Temperature 30...100 °C (86...210 °F), see Measuring Blocks, Group 019. (Fluid Level needs to be correct!)
    • Selector Lever in P
    • Ignition ON
    • Engine ON (Idling) for one minute or more
    • Brake Pedal operated (hold for the whole procedure)
    • Throttle Pedal not operated

    NOTE: Be sure to perform the following steps in the sequence shown, followed by the defined test drive.
    [Select]
    [02 - Transmission]
    [Basic Settings - 04]

    Transmission Tolerances (Engaged Calibration)

    Group 061
    [Go!]


    • When you go to Basic Settings 061 and click GO the screen may look like this: Basic Settings 061
    • Wait until the numbers quit moving and the trans will quit making noises. Basic Settings switches to On when finished: Basic Settings 061

    Wait until Basic Settings has switched to ON and all numbers have stopped moving. This may take one minute.

    Transmission Tolerances (Synch. Point. Measurement)

    Group 060
    [Go!]


    • When you go to Basic Settings 060 and click GO the screen may look like this: Basic Settings 060
    • Wait until the numbers quit moving and the trans will quit making noises. Basic Settings switches to On when finished: Basic Settings 060

    Wait until Basic Settings has switched to ON and all numbers have stopped moving.
    Clutch Adaptation

    Control Module Software Version < 0800:
    Group 062
    [Go!]
    Activate the Basic Setting.
    [ON/OFF/Next]

    Special notes.

    • When found in the early software level (0627/0628 )(8N) Audi TT:
      • Basic Settings group 062 may take several minutes to complete. The final values may report: [18 | 18 | .285 | .24] and Basic Settings will report ON when finished.
      • If Basic Settings group 062 reports ERROR:| Group 062| Not | Available try test driving the vehicle and repeating at normal operating temp.


    Internal Ref: ST?ID=66725 and E?ID=309867
    Control Module Software Version >= 0800 :
    Group 067
    [Go!]
    Activate the Basic Setting.
    [ON/OFF/Next]

    Reset Values (Clutch Safety Function)

    Group 068
    [Go!]
    Activate the Basic Setting.
    [ON/OFF/Next]

    Reset Values (Pressure Adaptation)

    Group 065
    [Go!]
    Activate the Basic Setting.
    [ON/OFF/Next]

    Reset Values (Steering Wheel Paddle Installation)

    Group 063
    [Go!]
    Activate the Basic Setting.
    [ON/OFF/Next]

    Reset Values (ESP & Tip Cruise Control Installation)

    Group 069
    [Go!]
    Activate the Basic Setting.
    [ON/OFF/Next]

    [Done, Go Back]
    Switch off Ignition, wait 10 Seconds and switch it back on.
    [Fault Codes - 02]
    Check and clear fault codes after successful test.
    [Close Controller, Go Back - 06]
    Perform the Defined Test Drive.


    Special Procedures

    Defined Test Drive

    Suggested test drive after replacing the mechatronic or successful basic setting.

    Prerequisites:


    • Fluid Temperature 30...100 °C (86...210 °F), see Measuring Blocks, Group 019.
    • Do Not use Cruise Control.

    Drive in Tiptronic Mode from stand still up to 6th Gear.
    While doing that make sure to drive in Gears 3 or 5 for approx. 5 minutes and also in 4 or 6 for approx. 5 minutes.
    The engine speed window for all gears is 1200 - 3500 RPM (for clutch calibration).
    Perform one sharp braking followed by a full throttle acceleration (oil return check) while in Drive, Not Tiptronic Mode.
    Evaluate creep and starting-off points.
    Check for leaks.

    NOTE: If the test drive cannot be performed in the recommended way or the necessary time, any remaining adaptations will be performed automatically during normal driving.
    Special Notes


    • Some modules do not require the use if the [ON/OFF/Next] button. If an Error is displayed after clicking the button, or the Basic Settings status does not switch to On, let the selected group and procedure finish on its own.


    • It is normal for the transmission to make noise while the tolerances are adapting. Do not exit or abort the Basic Settings sequence prematurely if you hear clacking noises.


    • Customers with TDI's have reported that an RPM range of 2000-2500 rpm is sufficient.




    Don
    Please don't PM to ask questions about coding, or vehicle repairs. The better place to deal with these matters is on-line, in the forum proper. That way you get the benefit of the expertise of the wider forum! Thank you.

  3. #3

    thank you for that, can it be done/activated from OBDeleven, or do i need VCDS cable + subscription etc..

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
| |